Jewelry PouchStep 1: Supplies fabric scraps,small piece of cardboard,scissors,thread,measuring tape. 2 yards of Ribbon. Sewing machine. Add Tip …Step 2: Cut Fabric Circles Cut 2 circles 14 and 2 circles 9. …Step 3: Sew Button Holes …Step 4: Sew Circles Together …Step 5: Cut Cardboard Circle …Step 6: Sew Layers Together …Step 7: Sew Pockets …Step 8: Sew Casing for Ribbon …More items
How to make homemade pouches?
Step-by-Step InstructionsChoose your puree and prepare it. Let it cool as needed. (Or pull out the yogurt or applesauce.)Fill the pouch,making sure that the cap is on if using the kind with the zipper opening on the bottom. (Otherwise it will all run right out the top!)Store in the fridge or serve to baby.
How do you make a jewelry pouch?
Large outside circle – fold fabric in half and finger press. …Large outside circle – this step is to add the eyelets. …For each circle,place right sides together and pin. …Turn circles right side out. …Large circle – this step is to sew the casing. …Cut 3 batting pieces. …Turn the large circle so that the outside fabric is facing down [Eyelets face outwards]. …More items…
How to make a mobile phone pouch?
Trace your phone onto a sheet of paper.Draw your pattern using a black marker. Make sure the design touches the sides.Cut out the template along the outline.Tape the template to the back of your phone.
How to make a smoker pouch?
These DIY Smoker Boxes Are Perfect for Quick Weeknight GrillingFold them into pockets. Start off by taking a sheet of foil (six to eight inches long) and lay it flat on a work surface. …Grab the wood chips. …Poke a few holes. …Keep a few extra under your grill. …Put the pouches in the grill first. …Pick quick-cooking recipes. …Season the food and add it to grill. …Let them cool. …
How to use fusible interfacing?
Kat recommends a lightweight fusible interfacing. I actually used fusible fleece for a little more padding. Transfer the button hole markings to the outer fabric piece. You should have two button hole markings directly across from each other. You will be threading the cording through these button holes.
How to make a pocket divider with a medium circle?
With the outer medium circle facing up transfer the markings for the pocket dividers and the center circle. Place the medium circle onto the lining of the outer circle with the pocket marking facing up and center. Stitch the small circle through all layers. Stitch each pocket divider to complete the pockets.
How to sew a circle in a hat?
Sew the large circles right sides together using a 1/4″ seam allowance. Clip the curves. Turn right sides out through the hole you cut in the center of the lining. Press well. Repeat for the medium circle. Edgestitch both circles.
How to make a circular pouch for jewelry?
Using a safety pin or a bodkin at one end of the cording, feed the cording through one of the button holes all the way through so it comes out the same button hole. Tie the ends together so they don’t go back through the hole. Repeat for the other button hole.Add your jewelry and pull the bag closed. You have now finished your circular jewelry pouch.
How to make a ring with ribbon?
Cut 2 pieces of 3/8" wide ribbon, 36" long. Place a safety pin on one end and push through one of the button holes, through the casing and all around and out of the buttonhole next to the one it went in. Tie the ends together in a knot. On the opposite side of the circle, put the safety pin on the end of the other ribbon and push it through one of the other buttonholes and through casing, out through the one next to it and tie the ends of ribbon together in a knot. Pull ribbons to close the jewelry pouch and tie into a bow.
How many pins to sew a pocket?
Place 8 pins around the small circle, evenly spaced, marking the stitching for the pockets. Sew from the edge of the cardboard to the outside edge of the small circle at all 8 places.
How to make a buttonhole with scrap fabric?
Place 2 small pieces of scrap fabric on the wrong side of one of the large fabric circles, on the underside of where the buttonholes will go. This will help stabilize the fabric as you sew. The buttonholes will be 1-1/2" from the outer edge. Sew 2 about 1/2" apart and then sew the other two on the opposite side of circle.
How to sew a drawstring on a presser foot?
Remove water soluble lines or chalk marks. Line up left side of presser foot with the inner circle and sew all the way around. Then line up that stitch line with the left side of the presser foot and move the needle all the way to the left. Stitch around again to create the casing for our ties/drawstring.
How to make a drawstring tie?
Start from 1 slit and thread all the way around and come out the same slit. Then take the other tie and insert that into the 2nd slit, going all the way around and coming out the same slit to create the drawstring. Cinch up drawstring and cut ties to desired side. Knot or fray check the ends.
How much seam allowance do you need to sew a circle?
Sew around the pinned circles using a 1/2 seam allowance leaving a 1 ½ inch opening for turning right side out.
How many fat quarters are needed for jewelry pouches?
1 Fat Quarter or (1) 18 x 22 inch piece of fabric will make 1 jewelry pouch. If you would like the coordinating print, you can make 2 jewelry pouches with 2 fat quarters.
How many pockets can you make with a ruler?
Take your ruler and draw lines across the smaller circle with a water soluble pen to create the pockets. It’s best to do a minimum of 4 pockets and maximum of 8. Sew along those lines back stitching well at the the beginning and end. Remove water soluble lines or chalk marks.
How to make a fabric liner?
Anchor the pushpin in the center of your fabric, place a pen or pencil in the hole and, holding the pushpin steady, drag the pencil around in a circle. Make a second circle the same size, this will be the liner (lime green for mine). Cut them out. Now repeat to make 2 smaller circles.
How far apart are pie pins?
You can kind of eye-ball it to get them as close to the same size as possible. The pins marking each of my pie sections were 3 5/8" apart. For each pie section, sew a line from the circle you made in the previous step to the edge of the small fabric piece.
How to tie a drawstring with a safety pin?
Catch one end of the ribbon or chord (drawstring) in a safety pin and insert into one of the holes. Use the safety pin to push the chord through the channel, all the way around (ignore the other hole when you get to it, just go right past it). Tie the ends together in a simple knot.
How to make a hole in a circle?
Cut a small slit in the outside fabric only, between the two seams. Cut another slit in the outside fabric only, between the two seams, but on the opposite side of the large circle. With needle and thread, reinforce the edges of the hole with a whip stitch. Repeat for other hole.
How to make a purple purse?
Step 1: Cut the Pieces. I’ll be using different coordinating fabric scraps for each piece. The purple with swirly vines will be the outside of the bag. Starting with the fabric for the outside of the bag, lay it on the table with wrong side up, place your dinner plate on it and trace around.
How to sew a velvet bag?
With right sides together, sew along the bottom of the bag for the velvet and for the lining leaving an opening in the seam on both sides of the velvet and lining from about 1” from the top line to 2” from the top. In other words, you will stitch the pieces together starting at the top and when you get to about 1”, lift the foot of the sewing machine and advance the fabric another 1” before you begin sewing again. This will be the opening that you’ll use to run the drawstring through. The inch at the top will create a ruffle when the drawstring is pulled tight.
How big should a velvet pouch be?
Now let’s talk about size. There’s no exact pattern for making a velvet jewelry pouch so it can be whatever size you want your bag to be (how much goodies do you have to put in it?). If you allow a 1/2“ seam line and you want an opening of 8” then make sure your top line is 9”. So, whatever size you want to opening of the bag to be cut it roughly 1” larger to allow for the ½” seam on each side.
Can you tie a knot on drawstrings?
Secure your drawstrings in any creative way you can think of. If you just want to tie a knot, that works just fine. If you want to string beads on the ribbons that’s great too. You can make it as simple of as ornate as you want.
Can you make a sleeve as deep as you want?
Same thing for the depth. It can be as deep as you want but of course it is restricted to the piece of fabric you have .